YEAR: 1977

Material: Cr-Hr-Hrpu-Hsla
Material Shear Stress: 60,000 PSI
Weight Capacity: 45,000 Lbs.
Material Width: 60"
Material Thickness: 0.028" - 0.280"
Coil I.D. Entry: 24" - 30"
I.D. Exit: 20"
Coil O.D.: 72" Entry and Exit
Line Speed: 250 FPM and 750 FPM Constant
Operating Modes: Pull Thru - Drive Assist - Loop
Line Direction: Right to Left

Consisting of the following:

-Entry Pit Type Coil Car:
Model: 40-72-36
Capacity: 40,000#
Hydraulic Lift & Travel
Approx. 30" Vertical Lift
(2) Powered Blocker Rolls on Top
Self-Contained Hyd. Power Unit
10 HP AC Motor, 1730 RPM, 575 V
Overall Size: 91" L x 39" W x 93" High

-Mandrel Uncoiler: New in 1998
Model: SMU-DB-45-72-24-62
S/N: 2676-02-98
Capacity: 45,000# x 72" O.D.
Hydraulic Expansion
61" Face Pumpkin Tooth Mandrel
Overarm Holddown Roll - Powered
Slide Base
Wichita Water Cooled Brake
Hydraulic Motor Feedup
Passline: 48" from Floor to center of Mandrel
Overall Size: 195" L x 86" W x 98" High
26,000 lbs.

-Entry Unit:
Model: 60-F-SH
S/N: 2676-5-77
Peeler Table with Hydraulic Lift and Extend
Photo Eye Edge Detector
Entry Driven Pinch Rolls
(3) Flattening Rolls (with Bottom Pinch Roll)
Exit Roller Type Side Guides, Powered Adjustment
Crop Shear w/64" x 4" x 1" Blade
Upcut Type Actuated by (3) - 7" Bore Hydraulic Cylinders
Feedup Table, Drop Away Type for Crop Removal
Overall Size: 132" L x 99" W x 93" High
25,000 lbs.

-Injector Type Slitter Heads:
(2) Heads
Model: SES-LHll-1613-9
S/N: 2676-6-77 and 2676-7-77
9" Dia. x 66" Face Arbors
Single Eccentric Arbor Adjustment
40 HP AC Motor Feed-Up Drive, 1750 RPM, 575 V
Thru Renold RA Reducer w/15:1 Ratio
60 HP Reliance DC Drive Assist Motor, 1750/2100 RPM, 500 V
Thru Renold RA Reducer w/10:1 Ratio
Overall Size: Slitter Heads: 136" L x 45" W x 92" High; 17,000 lbs. (each)
Drive: 126" L x 68" W x 67" High; 8,500 lbs.

-Slitter Head Transfer Gantry:
Fabricated Overhead Structural Steel Framework
Powered by 2 HP AC Gearmotor

-Slitter Head Set-Up Buggy:
Fabricated Steel Base supported on (4) Wheels and capable
of (2) Position Location by Hydraulic Cylinder.

-(2) Scrap Winders:
Model: HSW-MD
Capacity: 1" Wide x 0.280" Thick Strip
Bundle Size: Approx. 15" Wide x 30" Dia. (3,000#)
Inspection Table over the top
Bottom Drop out of the Scrap Ball
Hydraulic Motor Wind
Scrap Oscillator
Overall Size: 70" L x 60" W x 74" High
2,800 lbs. (each)

-Scrap Removal Cart:
Overall Size: 134" L x 44" W x 29" High

-Pit Catenary Roll Table:
Overall Size: 95" L x 77" W x 67" High

-Pit Cross Over Table:
Attached to Entry Side of Tension Stand

-Tension Stand:
Model: 60 DB-STU
Entry Separator Tooling Bar
Pad Type Tension Unit
Air Bag Type Tension Control
Exit Driven Pinch Rolls
Threading Table to Recoiler
Overall Size: 245" L x 102" W x 88" High (with Pit Table)
20,000 lbs.

-Recoiler: New in 1998
Model: HGR-45-72-20-60
S/N: 2676-10-98
Capacity: 45,000# x 72" O.D.
20" Dia. x 70" Face Drum
Hydraulic Grip & Expand
Hydraulic Pushoff
Overarm Separator
200 HP DC Main Motor, 650/1950 RPM
Horsburgh & Scott 2 Speed Reducer with 47.14:1 and 16.29:1 Ratios
Overall Size: 192" L x 122" W x 104" High
34,500 lbs.

-Exit Floor Mount Coil Car:
Model: 40-60
S/N: 2676-12-77
Side Mast Design
65" Bed Width
5" Dia. Camrolls
6" Bore Hydraulic Lift Cylinder
Approx. 20" Vertical Lift
Self-Contained Hydraulic Power Unit
7.5 HP AC Motor, 1730 RPM, 575 V
Narrow Coil Retaining Arms
Cable Reel
Approx. 12" from Floor to bottom of "V" Cradle
Overall Size: 92" L x 75" W x 87" High
12,500 lbs.

-2 Arm Exit Turnstile:
Model 2TS-49-0-72-16
40,000# Capacity each Arm
Approx. 68" Useable Arm length
20" Min. Coil I.D. Capacity
Mechanical Pushoff by Hydraulic Motor/Reducer
Powered Rotation by Hydraulic Motor
Passline: 58" from Floor to Top of Arm
Overall Size: 187" L x 54" W x 88" High
8,000 lbs.

-Main Operators Control Panel:

-Auxiliary Pushbutton Station:

-AC Electrics Panel:

-Less DC Electrics:

-Control Unit for Edge Guide:

-Water Chiller for Uncoiler Brake:

-Slitter Tooling Included:

-Removed and in storage: Toledo, OH.