|
Materials: HRS, CRS, Galv.
Coil Width Range: 12" - 74" (untrimmed)
Thickness Range: 0.075" - 0.250" (approx.)
Maximum Shear: 50,000 PSI
Maximum Yield: 50,000 PSI
Maximum Coil Weight (Entry): 60,000#
Maximum Coil Weight (Exit): 40,000# (Approx./Recoiler)
Coil I.D. (Entry): 20" - 24" (Nominal)
Coil I.D. (Exit): 20"
Maximum Coil O.D. (Entry): 84"
Maximum Coil O.D. (Exit): TBD
Line Direction: Left to Right
Mode of Operation: Pull Thru / Slitter Assist
Speed (Slitter Assist): 0 - 300 / 360 FPM (Approx.)
Speed (Pull Thru): 300 FPM Bare Drum (Approx.)
Sample Cut Chart (Arbor Only), Mild Steel @ 50,000 PSI
0.250" - (9) Cuts @ 72", (12) @ 60", (21) @ 48"
0.187" - (12) Cuts @ 72", (17) Cuts @ 60"
0.135" - (16) Cuts @ 72", (21) Cuts @ 60"
Consisting of the following:
-Entry Coil Car: Cincinnati
Mast Type
Floor Mounted
Self Contained Hydraulic Unit
Powered Lift and Traverse
Cable Reel
No Pendant Control
-Uncoiler: Paxson
Single Mandrel Type
Powered Expansion
Holddown / Powered Snubber Roll with Banding Slots
Wichita Water Cooled Brake (ATD 221)
Slide Base
Feedup Drive
No Water Cooler
-Entry Unit: Cincinnati
Extending Blade Type Peeler
Powered Entry Pinch Rolls
Powered Side Guides
-Provision for a Crop Shear (not available)
-Coil Breaker:
Powered Entry Pinch Rolls
Three (3) Work Rolls in a 0.500" Configuration
Hydraulically Powered
-Stationary Slitter Base: Paxson
Powered Entry Pinch Rolls
40 HP AC Feedup Motor (1765 RPM)
Gear Reducer (159.8/1)
200 HP DC Motor (1750 RPM, 500 Volts)
SM-Cyclo Gear Reducer (92.1 HP, 21/1)
-Two (2) Slitter Heads: Paxson
Crane Removable
10" Diameter Arbors
Manual Outboard Retraction
Powered Top Arbor Adjust
-Pit Section: Royalton
Mounted to Tension Stand
Entry Passline Roll
Carry Over Table
-Tension Stand: Royalton
Drag Type
Separator Arm on "Swing-Out" Frame
Internal Powered Pinch Rolls
Crop Shear - Down Cut Type (0.187" - 0.250" Max. Mild Steel Approx.)
Recoiler Feed Table
-Recoiler:
Hydraulic Pushoff
Hydraulic Expansion and Gripper
150 / 175 HP DC Motor (500/1600 RPM, 240 Volts)
Gear Reducer (28/1 Approx.)
Overarm Separator (needs to be attached to Recoiler)
-Exit Coil Car: Braner
Mast Type
Floor Mounted
47" Wide x 72" OD x 30,000# Coil Capacity
Self Contained Hydraulic Unit
Powered Lift and Traverse
No Pendant Control
No Cable Reel
-Two (2) Scrap Winders: Braner
Automatic Scrap Dump
Level Wind
14" x 45" OD Bundle (Approx.)
-Electrical Controls:
Main Operators Control Pandel (incomplete)
Misc. Control Consoles
AC/DC Control Cabinets (incomplete)
One (1) DC Drive for Recoiler (New)
-Hydraulic System:
One (1) 15 HP x 20 GPM HPU
One (1) 15 HP x 15 GPM HPU
-Tooling:
Shimless
Knives (New)
Steel Spacers
Rubbers
Separtor Tooling
-Installed but not under power.
|
