YEAR: 1993
Coil Width: 60" Coil ID: 20" - 24" Coil OD: 72" Gauge Range: 0.048" - 0.250" Line Direction: Left to Right
Consisting of the following:
-Peeler Table: Model PT/HD-60 S/N: 28057 Capacity: 60" W x 0.250" (2) Hydraulic Cylinders for Up / Down Movement (1) Hydraulic Cylinder for In / Out Movement of Peeler Blade Overall Size: 92" L x 74" W x 43" High -Pinch Rolls: Capacity: 60" x 0.250" S/N: 60" Face x 7" Dia. Rolls 62.5" Between Housings Air Cylinder Loaded 25 HP DC Motor with Blower 1750 RPM, 500 V Less Solid State Drive In-Line Gear Reducer Passline: 43" Overall Size: 157" L x 18" W x 63" High
-Crop Shear: S/N: 28069 Capacity: 0.250" x 60" Entry Driven Pinch Rolls 66" Face x 5.5" Dia., Rubber Covered Straight Blade Design: 64" Long Blade Hydraulic Down Cut Via 2 Parker Cylinders (2) - 6" Bore Parker Hydraulic Cylinders Passline: 40.5" Overall Size: 98" L x 48" W x 80" High
-Heavy Duty Straightener: (Sold) Model C15-60 S/N: 28061 Capacity: 0.048" - 0.250" Mild Steel Entry Side Guides Manual Adjustment (4) Entry Driven Coil Breaker Rolls 65" W x 7" Dia. (7) Work Rolls, 3 over 4 Design 65" W x 7" Dia. (2) Exit Driven Pinch Rolls 65" W x 7" Dia. Hydraulic Open / Close on Pinch Rolls Vertical Adjustment of Work Rolls by 3 HP AC Motor thru Jackscrews 50 HP DC Drive, Variable Speed Line Speed: 35 - 100 FPM Passline: 43" Overall Dimensions: Flattener 93" L x 124" W x 68" High Drive: 108" L x 36" W
-Lee Shaffer Coil End Joiner: S/N: 28072 Capacity: 60" x 0.250" Welding Platen: 64" Long Weld Clamp Station with Dual Weld Clamp Pads Weld Carriage Rides on Precision Screw Shaft driven by Vari-Speed DC Motor. Exit Passline Roll Controls for: Left Weld Clamp Open / Close Right Hand Weld Clamp Open / Close Platen Index Left / Right Torch Jog, Fwd / Run Weld Emergency Stop Rheostat for Torch Feed Speed Passline: 42" Overall Size: 100" L x 60" W x 65" High Note: Less Welding Unit
-Double Stub Edge Trimmer: S/N: 28064 Capacity: 60" x 0.250" Double-Stub Design 64" Max. Width Powered Width Adjustment Entry Edge Guides on (1) Unit Passline: 42" Less Drive Motors Overall Size: 165" L x 58" W x 52" High
-Scrap Chopper: S/N: 28066 Capacity: 0.250" Mild Steel (2) "Sets" of Entry Driven Pinch Rolls Each "Set" individually driven by Hydraulic Motors Chopper Blades: (2) 6" L x 2" W x 1.125" Thick Blades per Side Approx. 2" Max. Entry Strip Width AC Drive Motor Overall Size: 40" L x 36" Wide W x 52" High
-Gooseneck Scrap Conveyor: S/N: 28070 11" Wide Conveyor Belt AC Motor Driven Overall Size: 231" L x 28" W x 74" High
-In Storage: Toledo, OH
|