|
Consisting of the following:
Entry Coil Car: Stamco
48" Wide "V" Cradle
60" O.D. Max.
Approx. 18" Lift
Approx. 12" From Floor to bottom of "V" Cradle
Retractable Cable Reel
Self-Contained Hydraulics
12" High Bolt-On Riser for Small O.D. Coils
Overall Size: 91" L x 48" W x 80" High
-Uncoiler: Stamco
52" Face Mandrel
16" - 20" Coil I.D. Range
Hydraulic Expansion
Wichita Water Cooled Brake
AC Motor Threading Drive with Air Clutch
Holddown Arm with 8" Dia. x 36" Face Rubber Covered Roll
Hydraulic Motor Driven
Sliding Base
Passline: 43" From Floor to Center of Mandrel
Overall Size: 152" L x 84" W x 95" High
20,000 lbs.
-North American Edge Control: (Sold)
-Bridle Roll: (Sold)
62" Face x 8" Dia. Rubber Covered Rolls, Offset.
North American Light Box
Passline: 43"
Overall Size: 88" L x 56" W x 95" High
2,500 lbs.
-Slitter Head: Braner Turret Head (Sold)
6" Dia. x 53" Face Arbors
Parallel Arbor Adjustment
Jet Nuts
75 HP Reliance AC Inverter Duty Motor
1740 RPM, 460V with Blower
Thru Dodge Maxum Reducer with 7.52:1 Ratio
Passline: 43"
Approx. 13" Max. Knife Dia.
Overall Size: Slitter Head: 180" L x 44" W x 86" High
15,000 lbs.
Drive: 65" L x 24" W x 54" High
2,500 Lbs.
-Tension Stand: (Scrapped 9/2020)
Entry Rolls - Top Roll: 62.375" Face x 8.5" Dia., Rubber Covered
Hydraulic Cylinder Loaded
Bottom Roll: 53.75" Face x 7" Dia. Rubber Covered
Top Roll Driven by 1 HP AC Motor, 1726 RPM, 208-230/460V
thru Reducer with 50:1 Ratio
Entry and Exit Tables
Hydraulic Cable Track
Unit is Mounted on Wheels to Traverse to Slitter Head.
Note: Air Bag for Tensioning is Missing.
Overall Size: 110" L x 82" W x 70" High
-Exit Passline Roll: (Scrapped 9/2020)
62" Face x 10" Dia. Rubber Covered Roll
Overall Size: 100" L x 28" W x 55" High
1,500 lbs.
-Scrap Winder: Loopco (Sold 1-14-2021)
12" W x 36" Dia. Scrap Ball Capacity
Hydraulic Motor Driven
Oscillate Wind
Manual Scrap Removal
Overall Size: 60" L x 42" W x 48" High
1,400 lbs.
-Recoiler: Stamco
15" Dia. x 54.5" Face Drum
Bolt-on Urethane Pads for 19" Dia.
Hydraulic Expansion
No Gripper Slot
No Pushoff
No Overarm Separator
100 HP Reliance DC Motor, 850/1700 RPM, 600 V w/Blower
Reducer w/16:1 Ratio
Passline: 42.5" from Floor to Center of Drum
Overall Size: 172" L x 92" W x 81" High
-Exit Coil Car: SES (2012)
25,000 lbs. x 80" O.D. Capacity
54" Wide "V" Cradle
Horizontal Rotation of "V" Cradle by Hyd. Motor
4" Dia. Camrolls
34" Vertical Lift
Parker Series 2H Hydraulic Lift Cylinder, 6" Bore x 34" Stroke
Approx. 25" from Floor to bottom of "V" Cradle
Holddown Arm with Phenolic Spacer Rings.
Self-Contained Hydraulics
10 HP Motor, 1750 RPM, 208-230/460V
Heat Exchanger
Gleason Heavy Duty Retractable Cable Reel
Overall Size: 136" L x 77" W x 108" High
17,800 lbs.
-Main Hydraulic Power Unit: (Sold)
40 HP AC Motor, 1771 RPM, 230/460V
Approx. 80 Gallon Reservoir
Overall Size: 58" L x 45" W x 45" High
-Main Operators Control Panel:
Overall Size: 36" L x 18" W x 48" High
-Tooling: Knives, Spacers and Rubber Stripper Rings Included (Sold)
-Line Direction: Left to Right
-Removed and in Storage; Toledo, OH.
|
