Affiliated Companies: Excel Industries, Inc. and H.K. Holdings, Inc.

48" x 0.050" Strilich Cut to Length Line

Ref # 7965-C

Click on photo to enlarge

YEAR: 1998


STRILICH "PANTHER" CUT TO LENGTH LINE

COIL WIDTH: 24" - 48"
MATERIAL TYPE: ELECTRO-GALVANIZED, CR, PREPAINTED
MATERIAL THICKNESS: 0.027" - 0.050"
LENGTH ACCURACY: +/- 0.030"
LINE SPEED: 75 FPM MAXIMUM ROLL SPEED
(125 MAX @ 0.048" MATERIAL THICKNESS)
SHEAR CUTS: 25 CUTS MAXIMUM @ 18" FEED LENGTH
SLIT CUT CAPACITY: 5 CUTS OF .050"
MODE OF OPERATION: SINGLE EDGE OPERATION, FEED TO STOP
ELECTRICALS: 480 V / 3 PH / 60 HZ.

CONSISTING OF THE FOLLOWING:

-LESS UNCOILER
(CAN BE PROVIDED AT EXTRA COST)

-ADJUSTABLE ENTRY GUIDE:
MAXIMUM MATERIAL WIDTH: 48"
FOUR (4) SIDED HARDENED PLATE TYPE ENTRY GUIDES
ONE SIDE IS FIXED WITH THE OTHER SIDE BEING ADJUSTED THROUGH HANDWHEEL
ENTRY CATENARY SECTION FOR MATERIAL LOOP SUPPORT
ENTRY GUIDE AND CATENARY ROLL OUT OF THE WAY TO SET UP THE SLITTER

-QUICKSET SLITTER:
4" DIAMETER ARBORS x 48" WIDE
ARBORS MOUNTED IN HEAVY DUTY TAPERED ROLLER BEARINGS
DRIVEN THROUGH COMMON DRIVE WITH STRAIGHTENER
ADJUSTABLE OUTBOARD SQUARING GUIDE - MANUAL ADJUSTMENT
5 SETS 46SK D-2 MATERIAL SLITTER KNIVES
5 SETS 46RS RUBBER STRIPPER RINGS

-STRAIGHTENER:
MAXIMUM STRIP WIDTH CAPACITY: 48"
MATERIAL THICKNESS CAPACITY: 0.050"
30 HP VARIABLE SPEED AC VECTOR DRIVE GEARED FOR 75 MAX. ROLL SPEED
5 WORK ROLLS (2 OVER 3) - 3" DIAMETER HARDENED AND GROUND
POWERED 4" DIAMETER AIR LOADED ENTRY PINCH ROLLS
ALL WORK ROLLS AND PINCH ROLLS ARE CHAIN DRIVEN
CENTRALIZED MANUAL GREASE POINTS PROVIDED FOR WORK ROLL AND PINCH ROLL
BEARING LUBRICATION.
END HOUSINGS AND BEARING BLOCKS TO BE HEAVY DUTY MACHINED STEEL
HEAVY DUTY WELDED STRUCTURAL STEEL FRAMEWORK
TOP WORK ROLL HEAD VERTICAL AND BANK ADJUSTABLE VIA (4) ANTI-BACKLASH
SCREWJACKS.
AUTOMATIC NON-CONTACT LOOP CONTROL AUTOMATICALLY CONTROLS SPEEDS OF
MATERIAL THROUGH STRAIGHTENER.

-ELECTRONIC DIGITAL LENGTH CONTROL MEASURING SYSTEM:
PROGRAMMABLE CONTROLLER WITH BUILT-IN BATCH COUNTER AND RATE MULTIPLIER
MAIN OPERATOR CONTROL CONSOLE
HEAVY DUTY ENCODER MOUNT

-HYDRAULIC CUTOFF SHEAR:
MAXIMUM STRIP WIDTH CAPACITY: 48"
MATERIAL THICKNESS CAPACITY: 0.050"
CUTS PER MINUTE: 25 MAXIMUM
STROKE PER MINUTE: 60 MAXIMUM
HYDRAULIC ACTUATED CUTOFF DIE COMPLETE WITH (4) SIDED D2 HC-HC CUTOFF BLADES

-COMMON SUPPORT BASE:
HEAVY-DUTY WELDED STRUCTURAL STEEL BASE CONTAINING THE ENTRY GUIDE, SLITTER,
STRAIGHTENER AND SHEAR, FOR QUICK AND ACCURATE INSTALLATION.
NO FOUNDATION WORK REQUIRED.

-TRANSFER BELT CONVEYOR:
MAXIMUM SHEET WIDTH: 48"
TRANSFERS SHEETS OR STRIPS FROM SHEAR
FULL WIDTH ENDLESS TYPE BELT
QUICK AND SIMPLE BELT ALIGNMENT ADJUSTMENT
2" DIAMETER CONVEYOR DRUMS
48" LONG BED SECTION ALLOWS LIFT TABLE TO FIT UNDER CONVEYOR FOR EASY
OPERATOR STACKING.
VARIABLE SPEED DRIVE

-HYDRAULIC POWERED LIFT TABLE:
MAXIMUM BUNDLE WEIGHT: 2,500 LBS.
MAXIMUM WIDTH CAPACITY: 48"
MAXIMUM LENGTH CAPACITY: 48"
SELF CONTAINED HYDRAULIC PUMPING UNIT
HEAVY DUTY DESIGN
POWERED ROLLER TYPE CONVEYOR TO BE MOUNTED ON LIFT TABLE DECK FOR
END DISCHARGE OF STACKED MATERIAL.
LIFT TABLE TO BE MOUNTED ON CASTERS AND ON STEEL TRACK AND IS MANUALLY
MOVED IN AND OUT FROM UNDER CONVEYOR FOR STACKING OF MATERIAL.

-CONTROLS:
FULLY INTEGRATED OPERATOR CONTROL CONSOLE FOR COMPLETE LINE OPERATION.
ALL ELECTRICAL, HYDRAULIC AND PNEUMATIC CONTROLS SUPPLIED.

-CLEANED, WIRED AND TESTED

-NOTE: LINE COST $249,000. WHEN NEW IN 1998.





Your machine has been added to the Cart.

Click the Checkout button below or continue adding machines to the Cart.

0

Main Office  |  723 Phillips Avenue, Bldg. D2 Toledo, Ohio 43612  |  Phone: (419) 841-3586  |  Fax: (419) 841-2986  |  Email: sales@dnhmachinery.com