Affiliated Companies: Excel Industries, Inc. and H.K. Holdings, Inc.

66" x 6.50" x 40,000# Stamco Slitting Line

Ref # 6497-HK

Click on photo to enlarge

YEAR: 1985


This is a high speed coil slitting line.
It was originally built in 1985/6 by Monarch Stamco.
The following product mix was run on this line:

1) 5-out Can Stock
2) 10-out Can Stock
3) 12-out Can Stock
4) Brazing Stock
5) Lid Stock

Gauge and Coil Limitations:

Gauge Max: 0.075" (1.90 mm)
Gauge Min: 0.005" (0.12 mm)

Entry Coil Width: 30" - 66" (760 - 1676 mm)
Exit Coil Width: 0.75" - 66" (20 - 1676 mm)
Entry Coil O.D.: 40" - 96" (1015 - 2440 mm)
Exit Coil O.D.: 20" - 96" (508 - 2440 mm)
Coil Weight Max: 40,000 lbs (18,000 kg)
Approx. Cuts: 30 of 0.020" (0.50 mm)
16 of 0.030" (0.762 mm)
8 of 0.075" (1.90 mm)
Operational Modes: Tight line and single loop
Hand of Line: Right hand
Line Speed: 0 to 2000 fpm (610 mpm) @ 20" (508 mm) Bare Drum Speed
50 fpm (15 mpm) - jog/thread

Equipment Specifications:

-Turnstile: Stamco
Type: 4-arms w/Power Rotation
C-Hook Type Arms will accept 16" (406 mm) I.D. Coils
45" Usable Arm Length
Hyd. Motor: 1 hp
8 cu.in/rev @ 113 rpm = 4 gpm
Pump: 8 gpm @ 1000 psi
Turnstile Detente Cylinder: 3.25" bore, 2.5" stroke
Passline Height: 46.5" from Floor to Top of Arm (1181 mm)
Overall Length: 197.5" (5016 mm)
Base Size: 60" Dia. (1524 mm)

-Coil Car: Southworth
Scissor lift type
72" (1830 mm) Long "V" Cradle
Approx. 32" (812 mm) from Floor to bottom of "V" Cradle
Core remove and dump feature
System Pressure: 1800 psi
Rise Time: 56 seconds
Tilt Time: 2 - 3 seconds
Traverse Speed: 40 fpm (12 mpm)
Hydraulic Power Supplied by Uncoiler
Overall Size: 72" (1830 mm)L x 78" (1980 mm)W x 38" (965 mm)High

-Mandrel Type Uncoiler: Stamco
Sales Order: 404-84-9B
Machine # 4453
69.5" (1765 mm) Mandrel Face Width
Hydraulic Expansion
Expansion Range: 15" to 17" (381 - 432 mm)
Cylinder: 8" bore, 6" stroke
Drive Motor: 125 hp DC, 300/1800 rpm, 240 V
DC Holding Brake
Reducer w/2.972:1 Ratio
Blower Motor: 1.5 hp, 1730 rpm
Lube Pump Motor: 1.5 hp, 1800 rpm
Attached Holddown Roll
Hydro-Motor: 23.8 cu.in/rev @ 45 rpm = 6 gpm
Lift Cylinder: 4" bore, 17" stroke
Roll: 8" dia., 18" face, polyurethane cover, 80 - 90 durometer
Passline: 54" (1371 mm)from Floor to Center of Mandrel

- Edge Guide Unit: MEA
Type: 24" (610 mm)positioner with LE105 edge guide laser sensor
Pump Drive: 20 hp, 1150 rpm
Hyd. Tank Capacity: 150 gallons
Pump: 20 gpm @ 1200 psi

- Coil Peeler Table:

- Pinch Roll And Drive: Stamco
Drive Motor: 20 hp, 850/2300 rpm
Lift Cylinders (2 ea): 3.25" bore, 7" stroke
Rolls: 1 ea, 8" dia., 72" Face, polyurethane cover, 85 - 95 duro.
1 ea, 16" dia., 72" Face, polyurethane cover, 85 - 95 duro.

- Thread Table & Deflector Pinch Roll: Stamco
Upper Cylinders (2 ea): 3.25" bore, 7" stroke
Lower Cylinder (2 ea): 3.25" bore, 6" stroke
Swing Roll (2 ea): 3.25" bore, 5" stroke
Hydro-Motor: 23.8 cu.in/rev. @ 48 rpm = 6.5 gpm
Rolls (2 ea): 8" dia., 72" face, polyurethane cover, 85 - 95 durometer.

- Straightener: Stamco
Motor: Hydro-Motor,
11.9 cu.in/rev. @ 12 gpm
Lift Cylinders (2 ea): 3.25" bore, 4" stroke
Work Roll: 2.5" dia., 84.5" face
Back-up Roll: 4" dia., 72" face, 2" pitch grooved, right-hand spiral
Bridle Rolls (2 ea): 8" dia., 72" face, poly. cover, 85 - 90 duro.

- Slitter Heads: Stamco
Two Removable Heads
Sales Order 476-86-10A
Arbors: 6.5" (165 mm) Dia. x 72" (1830 mm)Face Arbors
Drive Motor: 75 hp DC, 300/1800 rpm, 240 V
Pinion Stand Gear Ratio: 1.5:1
Blower Motor: 1.5 hp, 1730 rpm

- Scrap Baller: Stamco
Drive Motor: 50 hp, 850/2550 rpm
Gear Ratio: 4.067:1
Eject Hydraulic Cylinder: 4" bore, 15" stroke
Traverse Hydraulic Cylinder: 4" bore, 46" stroke
Air Cylinder: 8" bore, 21" stroke
Air Cylinder: 6" bore, 7" stroke

- Synchro-Wind Tension Stand: Stamco
Machine No.: 4460
Sales No.: 418 84 24A
Entry Separator Tooling Bar
Entry Passline Roll
Tension Rolls (2 ea): 16" (406 mm) dia. x 76" (1930 mm) face
serrated polyurethane covered
Drive Motor: 150 hp DC, 300/1500 rpm
Gear Ratio: 1:1
Blower Motor: 1 hp, 1725 rpm
Lift Hydraulic Cylinder (2 ea): 3.25" bore, 25" stroke
Air Cylinder: 2.5" bore, 2" stroke

- Exit Crop Shear: Stamco
S/N: 1363
Mechanical Operation
Capacity: 0.125" (3.17 mm) Mild Steel
74" (1880 mm) Long Blade
38" (965 mm) Passline Height
3 HP GE AC Motor, 1145 RPM, 220/440 V
Overall Size: 125" (3175 mm)L x 46" (1168 mm)W x 61" (1550 mm)High

- Exit Threading Table:

- Recoiler: Stamco
Drum: 20"(508 mm) Diameter x 84" (2133 mm) Face Width
Dual Direction Gripper (Over and Under Wind)
Powered Clamp and Expansion
Hydraulic Drum Cylinder: 10" bore, 6" stroke
Hydraulic Pushoff
Pusher Plate Cylinder: 4" bore, 107" stroke
Drive Motor: 125 hp DC, 300/1800 rpm
Gearbox Rated at 125 HP
Gear Ratio: 4.12:1
Blower Motor: 1.5 hp, 1800 rpm
Lube Pump Motor: 1.5 hp, 1800 rpm
Passline: 44" (1118 mm) from Floor to Center of Drum
Powered Outboard Support

- Entry Hydraulic Unit
Tank Capacity: 105 gallons
Motor: 15 hp, 1200 rpm
Pump: 26 gpm @ 1200 rpm
System Pressure: 850 psi

- Exit Hydraulic Unit
Tank Capacity: 150 gallons
Motor: 25 hp, 1200 rpm
Pump: 47 gpm @ 1200 rpm
System Pressure: 900 psi

-Line is in Storage: Toledo, Ohio









Your machine has been added to the Cart.

Click the Checkout button below or continue adding machines to the Cart.

0

Main Office  |  723 Phillips Avenue, Bldg. D2 Toledo, Ohio 43612  |  Phone: (419) 841-3586  |  Fax: (419) 841-2986  |  Email: sales@dnhmachinery.com